PLUMBING FOR BEGINNERS: THE ESSENTIALS FOR BATHTUB INSTALLATION

Plumbing for Beginners: The Essentials for Bathtub Installation

Plumbing for Beginners: The Essentials for Bathtub Installation

Blog Article

Call

The article author is making several good observations on How to Install a Bathtub as a whole in this content which follows.


Installing A Bathtub
Installing a bath tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is readily accessible, the project can relocate rapidly; if you have to open a wall surface to remove the old bathtub and also place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the brand-new one. Ensure you have qualified on your own for the task and are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is better to consider using one before you begin. Chances are you might need a specialist plumber to make tube links.
This write-up will certainly aid you set up a brand-new bathtub in your shower room if you have actually already purchased a new tub and also don't require to change the plan of your previous supply of water pipelines.
Your devices and also product list should make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Getting ready for the Installment


    Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
    Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
    Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its final position.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is detach the supply of water. After doing so, activate the taps to drain any type of water staying in the system. The process of removing the existing taps can be fairly troublesome as a result of the limited access that is typically the instance.
    Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleaned up of any old securing substance.
    Prior to going on to fit the brand-new faucets, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

    Setting up the Bathtub


    Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto four tiny factors.
    The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bath tub till the level reads degree.
    To set up faucets, fit the bottom of the furthest versatile faucet port to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
    Turn on the water system and check all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and likewise inspect the overflow electrical outlet and also the typical outlet for leaks.
    Lastly, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bath tub should wait up until the bathtub has actually been made use of at the very least when as this will certainly resolve it into its last placement.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Safeguard the faucet in place with the maker provided backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The former type needs to be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the area where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
    You can pick from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and also cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked paper or soft rope. Remember to always fill the bath tub with water prior to securing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly early if you do not take into consideration this motion prior to securing.
    Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the market. It is a good idea to fit the tiles making use of water-resistant or water-proof glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    I ran across that write up about A Step-by-Step Guide to Installing a Bathtub while looking around the search engines. Sharing is good. You just don't know, you may be doing someone a favor. We treasure reading our article about Tools You Need to Install a New Bathtub .


    We value timeliness.

    Report this page